Minimum design temperature means the temperature which is used for the design and construction of the shell not higher than the lowest (coldest) temperature (service temperature) of the contents during normal conditions of filling, discharge and transport.

Control Temperature ( C) 20 C

4.2.1.13.5 Portable tanks shall be fitted with temperature sensing devices.

During filling, the temperature of the refrigerated liquefied gas shall be within the limits of the design temperature range.

t actual temperature of the substance during filling (in C) when this temperature is unknown, let t 15 C

(b) the lowest set pressure of the pressure limiting device(s)

During filling, the temperature of the non refrigerated liquefied gas shall fall within the limits of the design temperature range.

(ii) the partial pressure (in bar) of air or other gases in the ullage space being determined by a maximum ullage temperature of 65 C and a liquid expansion due to an increase in mean bulk temperature of tr tf (tf filling temperature, usually 15 C tr 50 C, maximum mean bulk temperature).

(ii) the partial pressure (in bar) of air or other gases in the ullage space being determined by a maximum ullage temperature of 65 C and a liquid expansion due to an increase in mean bulk temperature of tr tf (tf filling temperature usually 15 C tr 50 C maximum mean bulk temperature) and

U thermal conductance of the insulation, in kW.m 2.K 1, at 38 C, t actual temperature of the non refrigerated liquefied gas during filling( C) when this temperature is unknown, let t 15 C.

For substances handled under elevated temperature conditions the design temperature shall be not less than the maximum temperature of the substance during filling, discharge or transport.

the partial pressure (in bar) of air or other gases in the ullage space being determined by the design reference temperature and the liquid phase expansion due to the increase of the mean bulk temperature of tr tf (tf filling temperature, usually 15 C, tr 50 C maximum mean bulk temperature).

For portable tanks equipped with a heating device, a temperature regulator shall be used to ensure the maximum degree of filling is not more than 95 full at any time during transport.

in which df and dr are the densities of the liquid at the mean temperature of the liquid during filling and the maximum mean bulk temperature during transport respectively.

6.6.3.5.5 In addition to filling, discharge and gas pressure equalizing orifices, shells may have openings in which gauges, thermometers and manometers can be fitted.

4.2.1.9.5 The requirements of 4.2.1.9.2 to 4.2.1.9.4.1 do not apply to portable tanks which contain substances maintained at a temperature above 50 ºC during transport (e.g. by means of a heating device).

Design reference temperature means the temperature at which the vapour pressure of the contents is determined for the purpose of calculating the MAWP.

T absolute temperature in Kelvin ( C 273) above the pressure relief devices in the accumulating condition

There's just silence and a cool temperature.

The installation and preparation were initiated in the third quarter of 1995 the installations are expected to be completed as of the fourth quarter of 1996.

4.2.1.9.5.1 The maximum degree of filling (in ) for liquids transported under elevated temperature conditions is determined by the formula

TP3 For liquids transported under elevated temperature conditions the filling limits prescribed in 4.2.1.9.5.1 shall be met.

This will typically involve the requirement to operate in temperature ranges from Hot Dry (Storage Temperature 71 C and Operational temperature without solar loading of 49 C), down to Cold (Storage Temperature 46 C and Operating temperature 46 C.

Scrotal temperature reflects intratesticular temperature and is lowered by shaving.

This takes the temperature of the canal and turns it into this four degrees of heat exchange.

Fusible elements used on portable tanks intended for the transport of elevated temperature substances shall be designed to operate at a temperature higher than the maximum temperature that will be experienced during transport and shall be to the satisfaction of the competent authority or its authorized body.

4.2.1.9.4 In these formulae, α is the mean coefficient of cubical expansion of the liquid between the mean temperature of the liquid during filling (tf) and the maximum mean bulk temperature during transport (tr) (both in C).

The thermometer fell to zero last night.

Temperature

Temperatures

Temp

Temperature

Based on the above, an annual heating degree day value is arrived at by calculating the differences between a reference or base temperature (for example, 18ºC) and the average temperature Ti for all the days i of one year, whose average temperature is below the base temperature.

Thus, the annual total of cooling degree days (CDD) index is calculated by summing the differences of the average temperature Ti and a base temperature (for example, 18ºC) for all days i of one year, whose average temperature is above the base temperature.

So temperature is high, you go that way, temperature is low, you go that way.

Thermometer

A thermometer can be used to determine the temperature of a sample. In a laboratory, special thermometers are used which can also be used within acids or bases.

The thermometer reads 10 degrees.

IMS is designed to measure the density and temperature of electrons in the ionosphere.

SJ It's cold.

It elevates the temperature.

Temperature Unit

fahrenheit

réaumurs

Degrees Fahrenheit