So, this thing is 0.75 millimeters.

The largest hole diameters were about 5 millimetres.

The largest crater of 5 millimetres in diameter was probably caused by a 1 millimetre particle.

The largest crater, 5 mm in diameter, was probably caused by a particle of 1 mm.

Tethers several thousand metres in length and a few millimetres in diameter might not survive for extended periods.

Figure 1 shows the result for a diameter threshold of 1 cm and 1 mm respectively.

This corresponds to a test vessel orifice diameter of about 11 mm.

The sun end was about four inches in diameter, and then it tapered over about 35 feet to about a millimeter at the Earth end.

(diameter)

The changes used are 7.0 cm in diameter and 14.7 cm in length the liner angle in 30 degrees, the thickness of aluminum liner is 2.1 mm.

12,000 rounds of 30 mm ammunition

34,770 rounds of 7.62 mm ammunition

12,000 rounds of 30 mm ammunition

34,770 rounds of 7.62 mm ammunition

1 82 mm mortar

5 60.75 mm mortars

Shells of more than 1.80 m in diameter shall be not less than 6 mm thick in the reference steel or of equivalent thickness in the steel to be used.

On EURECA the largest impact crater diameter was 6.4 millimetres.

On the European Retrievable Carrier (EURECA), the largest impact crater diameter was 6.4 mm.

It's about 500 kilometers in diameter.

There's the 20caliber again.

I could prove it quicker with a 20millimeter.

Shells of more than 1.80 m in diameter shall be not less than 6 mm thick in the reference steel or of equivalent thickness in the metal to be used.

6.6.2.4.7 When in the applicable portable tank instruction in 4.2.4.2.6, a minimum thickness of 8 mm, 10 mm or 12 mm is specified, it shall be noted that these thicknesses are based on the properties of the reference steel and a shell diameter of 1.80 m.

Used in Israeli 81 120 160 mm mortars and shells of various calibres, including 122 155 175 mm shells.

However, shells not more than 1.80 m in diameter shall be not less than 3 mm thick in the reference steel or of equivalent thickness in the metal to be used.

Shells more than 1.80 m in diameter shall be not less than 4 mm thick in the reference steel or of equivalent thickness in the metal to be used.

6.6.4.4.2 Shells of not more than 1.80 m in diameter shall be not less than 5 mm thick in the reference steel or of equivalent thickness in the metal to be used.

Such shells of more than 1.80 m in diameter shall be not less than 4 mm thick in the reference steel or of equivalent thickness in the metal to be used.

The charge is 7.0 cm in diameter and 14.7 cm in length.

1 107 mm rocket launcher

Listen, that's the 88!

For example, it is common practice to fit four 250 mm diameter bursting disks to a 20 ton tank.

6.6.2.12.1 The spring loaded pressure relief device required by 6.6.2.8.1 shall have a minimum cross sectional flow area equivalent to an orifice of 31.75 mm diameter.

It is estimated to have the capability to detect a particle 1 mm in diameter at a distance of 1 km.

The largest impact is located on the infrared telescope Multi Layer Insulation (MLI), with perforation of diameter of 4.5 mm.

M V will be 2.5 metres in diameter and 30 metres in length, and will weigh 35 tonnes.

(b) shell with a diameter of more than 1.5 metres

3 12.7 mm Doshka machine guns

Type Israeli 120 mm cluster bomb (CL3144 ICM)

Hear that 20caliber machine gun?

Issue him with a Colt. 32.

M V will be 2.5 metres in diameter and 30 metres in length, and will weigh 35 tons.

6.6.4.4.3 Shells of vacuum insulated tanks of not more than 1.80 m in diameter shall be not less than 3 mm thick in the reference steel or of equivalent thickness in the metal to be used.

2 medium calibre 14.5 mm machine guns, plus 84 rounds of ammunition