6.6.3.5.3 For filling and discharge openings the first shut off device shall be an internal stop valve and the second shall be a stop valve placed in an accessible position on each discharge and filling pipe.

6.6.3.5.2.1 When a portable tank is fitted with an excess flow valve the excess flow valve shall be so fitted that its seating is inside the shell or inside a welded flange or, when fitted externally, its mountings shall be designed so that in the event of impact its effectiveness shall be maintained.

No stop valve shall be installed between the shell and the pressure relief devices except when duplicate devices are provided for maintenance or other reasons and the stop valves serving the devices actually in use are locked open or the stop valves are interlocked so that the requirements of 6.6.4.7 are always fulfilled.

(i) the control devices for the operation of the valve are designed so as to prevent any unintended opening through impact or other inadvertent act

Bundles containing UN 1045 Fluorine, compressed, may be constructed with isolation valves on assemblies (groups) of cylinders not exceeding 150 litres total water capacity instead of isolation valves on every cylinder.

No stop valve shall be installed between the shell and the pressure relief devices except where duplicate devices are provided for maintenance or other reasons and the stop valves serving the devices actually in use are locked open or the stop valves are interlocked so that at least one of the duplicate devices is always in use.

6.6.2.5.2 All openings in the shell, intended for filling or discharging the portable tank shall be fitted with a manually operated stop valve located as close to the shell as reasonably practicable.

(a) an external stop valve fitted as close to the shell as reasonably practicable and

6.6.3.5.2 All openings with a diameter of more than 1.5 mm in shells of portable tanks, except openings for pressure relief devices, inspection openings and closed bleed holes, shall be fitted with at least three mutually independent shut off devices in series, the first being an internal stop valve, excess flow valve or equivalent device, the second being an external stop valve and the third being a blank flange or equivalent device.

4.2.1.13.10 Vacuum relief devices and spring loaded valves shall be provided with flame arresters.

(b) an external stop valve fitted as close to the shell as reasonably practicable and

No stop valve shall be installed between the shell and the pressure relief devices except when duplicate devices are provided for maintenance or other reasons and the stop valves serving the devices actually in use are locked open or the stop valves are interlocked so that at least one of the duplicate devices is always operable and capable of meeting the requirements of 6.6.3.8.

Military equipment in the form of night vision devices was also part of a shipment of arms to a warlord located in Mogadishu.

Shut off valves shall be closed after filling and remain closed during transport.

Anything else... sir?

(v) the valve shall continue to be effective in the event of damage to the external device for controlling the operation of the valve

6.6.4.5.2 Each filling and discharge opening in portable tanks used for the transport of flammable refrigerated liquefied gases shall be fitted with at least three mutually independent shut off devices in series, the first being a stop valve situated as close as reasonably practicable to the jacket, the second being a stop valve and the third being a blank flange or equivalent device.

The seacocks are the valves to drain out the boat.

Remote closure devices and self closing stop valves shall be operated to demonstrate proper operation

An officer...

4.2.1.13.7 The pressure relief devices shall consist of spring loaded valves fitted to prevent significant build up within the portable tank of the decomposition products and vapours released at a temperature of 50 oC.

Other openings, except for openings leading to venting or pressure relief devices, shall be equipped with either a stop valve or another suitable means of closure located as close to the shell as reasonably practicable.

Sea...

The excess flow valves shall be selected and fitted so as to close automatically when the rated flow specified by the manufacturer is reached.

(a) a self closing internal stop valve, that is a stop valve within the shell or within a welded flange or its companion flange, such that

The dragoon, you mean?

Cylinder head valve grinder

Valves and tubes

Throttle set.

Cut your throttle.

Open your throttle another crack.

So the valves at the bottom of those tubes there are like radio controlled airplane valves.

(b) Each valve shall be of the packless type with non perforated diaphragm, except that, for corrosive materials, a valve may be of the packed type with an assembly made gas tight by means of a seal cap with gasket joint attached to the valve body or the pressure receptacle to prevent loss of material through or past the packing

(e) all emergency devices and valves are free from corrosion, distortion and any damage or defect that could prevent their normal operation.

Civil Horizontal Valve

Vehicle jack Cylinder head valve grinder

Cylinder head valve grinder

What are the seacocks?

Open fuel valves.

15 The portable tank may be fitted with a device located under maximum filling conditions in the vapour space of the shell to prevent the build up of excess pressure due to the slow decomposition of the substance transported.

Each pressure receptacle with a wall thickness at any point of less than 2.0 mm and each pressure receptacle that does not have fitted valve protection shall be transported in an outer packaging.

For future launches of the Globalstar programme, an additional pyrotechnic valve will be installed on the upper part of the second stage oxidizer tank.

China s Resurgent Warlords

These are rebel officers who had been nominated in the context of the integration of the armed forces command they include leaders of armed groups in Ituri and mere warlords.

ASCs are currently used for wear resistant parts (seals and valves), cutting tools, bearings and thermal barrier coatings.