Equivalent thickness in reference steel _ mm

Stamp of expert who performed or witnessed the most recent test _

6.6.3.4.4 The equivalent thickness of a steel other than the thickness prescribed for the reference steel in 6.6.3.4.2 shall be determined using the following formula

6.6.2.4.6 The equivalent thickness of a metal other than the thickness prescribed for the reference steel in 6.6.2.4.3 shall be determined using the following equation

e1 required equivalent thickness (in mm) of the steel to be used

e1 required equivalent thickness (in mm) of the metal to be used

Shells of more than 1.80 m in diameter shall be not less than 6 mm thick in the reference steel or of equivalent thickness in the steel to be used.

6.6.4.4.6 The equivalent thickness of a metal other than the thickness prescribed for the reference steel in 6.6.4.4.2 and 6.6.4.4.3 shall be determined using the following equation

Shells of more than 1.80 m in diameter shall be not less than 6 mm thick in the reference steel or of equivalent thickness in the metal to be used.

Shells more than 1.80 m in diameter shall be not less than 4 mm thick in the reference steel or of equivalent thickness in the metal to be used.

6.6.4.4.2 Shells of not more than 1.80 m in diameter shall be not less than 5 mm thick in the reference steel or of equivalent thickness in the metal to be used.

Such shells of more than 1.80 m in diameter shall be not less than 4 mm thick in the reference steel or of equivalent thickness in the metal to be used.

Shells more than 1.80 m in diameter shall be not less than 6 mm thick in the reference steel or of equivalent thickness in the metal to be used, except that for powdered or granular solid substances of Packing Group II or III the minimum thickness requirement may be reduced to not less than 5 mm thick in the reference steel or of equivalent thickness in the metal to be used.

6.6.4.4.3 Shells of vacuum insulated tanks of not more than 1.80 m in diameter shall be not less than 3 mm thick in the reference steel or of equivalent thickness in the metal to be used.

Thickness

The degree of shielding required is highly dependent upon the nature (material, thickness etc.), location and orientation of the surface to be protected.

6.6.4.4.4 For vacuum insulated tanks, the aggregate thickness of the jacket and the shell shall correspond to the minimum thickness prescribed in 6.6.4.4.2, the thickness of the shell itself being not less than the minimum thickness prescribed in 6.6.4.4.3.

6.6.2.4.2 The cylindrical portions, ends (heads) and manhole covers of shells not more than 1.80 m in diameter shall be not less than 5 mm thick in the reference steel or of equivalent thickness in the metal to be used.

6.6.3.4.2 The cylindrical portions, ends (heads) and manhole covers of shells of not more than 1.80 m in diameter shall be not less than 5 mm thick in the reference steel or of equivalent thickness in the steel to be used.

L thickness of insulation layer m

L thickness of insulation layer m

6.6.2.4 Minimum shell thickness

6.6.3.4 Minimum shell thickness

6.6.4.4 Minimum shell thickness

Attention is drawn to the minimum shell thickness requirements, specified in 6.6.4.4.2 to 6.6.4.4.7.

This thickness shall be exclusive of any corrosion allowance.

Medium young, medium height.

6.6.2.4.1 The minimum shell thickness shall be the greater thickness based on

6.6.3.4.1 The minimum shell thickness shall be the greater thickness based on

6.6.4.4.1 The minimum shell thickness shall be the greater thickness based on

The thickness of aluminium liner is 2.1 mm.

(ii) is approximately of the same size and mass as the existing equipment and

Why can I say, I'll take my steak medium rare, I need size six shoes, but I won't say, Would you praise me this way?

Attention is drawn to the minimum shell thickness requirements for these shells specified in 6.6.3.4.

(e) Determine the internal structure of the asteroid, in particular the sizes of the main solid pieces, the average particle size and thickness of the regolith and of the debris layers in the space left between the main pieces

6.6.3.4.5 In no case shall the wall thickness be less than that prescribed in 6.6.3.4.1 to 6.6.3.4.3.

6.6.4.4.7 In no case shall the wall thickness be less than that prescribed in 6.6.4.4.1 to 6.6.3.4.5.

Attention is drawn to the minimum shell thickness requirements for these tanks specified in 6.6.2.4.1 to 6.6.2.4.10.

6.6.2.4.8 In no case shall the wall thickness be less than that prescribed in 6.6.2.4.2, 6.6.2.4.3 and 6.6.2.4.4.

It's created depositing layers of about four microns.

Minimum shell thickness (mm reference steel) Bottom opening requir ements

(a) the minimum thickness determined in accordance with the requirements in 6.6.3.4 and

thickness (mm reference steel)

However, shells not more than 1.80 m in diameter shall be not less than 3 mm thick in the reference steel or of equivalent thickness in the metal to be used.

Start with Medium difficulty level