Thermometer

The thermometer reads 10 degrees.

The thermometer fell to zero last night.

A thermometer can be used to determine the temperature of a sample. In a laboratory, special thermometers are used which can also be used within acids or bases.

Somebody knocked.

Contact Thermometer

Design reference temperature_ C

Minimum design temperature _ C

A thermometer.

Thermometers often go below zero.

Calculation of a temperature index

Design temperature range _ C to _ C.

Minimum design temperature means the temperature which is used for the design and construction of the shell not higher than the lowest (coldest) temperature (service temperature) of the contents during normal conditions of filling, discharge and transport.

The thermometer's on strike.

He used to call me his little thermometer.

During filling, the temperature of the refrigerated liquefied gas shall be within the limits of the design temperature range.

Based on the above, an annual heating degree day value is arrived at by calculating the differences between a reference or base temperature (for example, 18ºC) and the average temperature Ti for all the days i of one year, whose average temperature is below the base temperature.

Contact thermometers differ from regular thermometers in that they are connected to a heating coil, and are hence able to both sense and control the current temperature. In doing so, they allow experiments to be performed under a constant temperature. Contact thermometers work using a negative feedback loop once the desired temperature has been reached, the heating coil is deactivated when the temperature falls, the heating coil is reactivated.

It ought to be buzzing with plans to reduce the temperature, and with plans to live at the higher temperature and not at all costs, but efficiently and cheaply. And some such plans exist, things like swarms of mirrors in space to deflect the sunlight away, and encouraging aquatic organisms to eat more carbon dioxide.

The base and threshold temperatures for calculating the heating degree days are chosen to best satisfy this relation.

During filling, the temperature of the non refrigerated liquefied gas shall fall within the limits of the design temperature range.

How can you play outside with the thermometer in your mouth?

Computes the melting temperature for a nucleic acid duplex.

Shall I send a thermometer up to your room?

A sixinch celluloid scale. Thermometer. Some tweezers.

Design reference temperature means the temperature at which the vapour pressure of the contents is determined for the purpose of calculating the MAWP.

For substances handled under elevated temperature conditions the design temperature shall be not less than the maximum temperature of the substance during filling, discharge or transport.

We are taking a quiz today over air pressure.

(b) When applicable, the control and emergency temperatures indicated are appropriate, taking into account the design (e.g. insulation) of the IBC to be used.

This will typically involve the requirement to operate in temperature ranges from Hot Dry (Storage Temperature 71 C and Operational temperature without solar loading of 49 C), down to Cold (Storage Temperature 46 C and Operating temperature 46 C.

Scrotal temperature reflects intratesticular temperature and is lowered by shaving.

This takes the temperature of the canal and turns it into this four degrees of heat exchange.

This value for each portable tank type is as follows

We plan to launch this product in India in 2010, and the target price point will be 25 dollars, less than 0.1 percent of the cost of a traditional incubator.

Annual procurement planning

A microwave radiometer for sounding of temperature and humidity of the atmosphere has been developed for operational use.

Temperature

Temperatures

Temp

Temperature

(ii) Annual audit plan, budget and staffing

And of course, our thermometers only take us back 50 years or so here.

Thus, the annual total of cooling degree days (CDD) index is calculated by summing the differences of the average temperature Ti and a base temperature (for example, 18ºC) for all days i of one year, whose average temperature is above the base temperature.

the partial pressure (in bar) of air or other gases in the ullage space being determined by the design reference temperature and the liquid phase expansion due to the increase of the mean bulk temperature of tr tf (tf filling temperature, usually 15 C, tr 50 C maximum mean bulk temperature).

An essential step used by all Parties, when adjusting for temperature variations, is to calculate what is called a heating degree day (HDD) index.