Test pressure means the maximum gauge pressure at the top of the shell during the pressure test

OK, this is the route up Everest.

6.6.2.15.1 Each pressure relief device inlet shall be situated on top of the shell in a position as near the longitudinal and transverse centre of the shell as reasonably practicable.

6.6.3.11.1 Each pressure relief device inlet shall be situated on top of the shell in a position as near the longitudinal and transverse centre of the shell as reasonably practicable.

6.6.4.10.1 All pressure relief device inlets shall be situated on top of the shell in a position as near the longitudinal and transverse centre of the shell as reasonably practicable.

A half line by its start point, and another point somewhere on it.

So, the head of the curve can be sharper or flatter.

For insulated portable tanks, top fittings shall be surrounded by a spill collection reservoir with suitable drains.

Test pressure means the maximum gauge pressure at the top of the shell during the hydraulic pressure test equal to not less than 1.5 times the design pressure.

Yeah, I'm filling in for a friend of mine every once in a while over in Radio City.

Pots.

The top of the tank is provided with either a 1 mm opening which simulates the pressure relief valve (PRV) of the IBC or tank or a real PRV of a diameter which is scaled using the vent area to vessel volume ratio.

The temperature inside the tank is measured by means of three thermocouples, two located in the liquid phase (near the top and bottom) and one in the gas phase.

Maximum allowable working pressure (MAWP) means a pressure that shall be not less than the highest of the following pressures measured at the top of the shell while in operating position

(a) protection against lateral impact which may consist of longitudinal bars protecting the shell on both sides at the level of the median line

Maximum allowable working pressure (MAWP) means the maximum effective gauge pressure permissible at the top of the shell of a loaded portable tank in its operating position including the highest effective pressure during filling and discharge

And packed in its nose was a silver ball with two radios inside.

6.6.2.4.4 The cylindrical portions, ends (heads) and manhole covers of all shells shall be not less than 3 mm thick regardless of the material of construction.

It's better than doing pots.

They shall be placed at the top of the shell with their inlets in the vapour space and in no case shall they be shielded from external heat.

And if a cloud goes past, you can see a cloud on the tips where it's letting the light through.

Road tank vehicles, rail tank wagons, non metallic tanks and intermediate bulk containers (IBCs) are not considered to fall within the definition for portable tanks

And I've got to do the pots all week.

There are fewer and fewer people who are still available that you might infect, and then you get the plateau of the curve, and you get this classic sigmoidal curve.

But going from slinging some wire across rooftops in Boston to laying thousands and thousands of miles of cable on the Atlantic Ocean seabed is no easy matter.

Road tank vehicles, rail tank wagons, non metallic tanks, intermediate bulk containers (IBCs), gas cylinders and large receptacles are not considered to fall within the definition for portable tanks

For tanks

Candy

Any specific style? This one, this one...

Kettle, kettle on the hob

Unlike at Venus or Earth, many disturbances were seen in the pure upstream region in front of, but close to the magnetic field line tangent to the bowshock.

Maximum allowable working pressure (MAWP) means a pressure that shall be not less than the highest of the following pressures measured at the top of the shell while in operating position, but in no case less than 7 bar

The demarcation team shall fix pillar sites at the outer and westernmost tips of the perimeter of the plateau, linked by a series of straight lines traversing the valleys in between.

Peak to peak distance

Peak to peak distance

On the top, now, that is a temperature record of a mouse who has gone through the dotted line, the temperatures.

Spraycan

Water tanks

Take the pitcher.

(a) Portable tanks The tank shall be filled with water or any other non pressurized substance to approximately 97 of the tank volumetric capacity.

Bowler, bowler.

That's 18 shots. We've used two already.

For example, because of the constraints imposed by antenna size, for all practical purposes a single building top repeater could generate at most six spot beams using a 60 degree sectorial antenna.

Like a Morandi like the little bottles composing them like a still life.

(b) when leaking