Metal IBCs the IBC shall be filled to not less than 95 of its maximum capacity for solids or 98 of its maximum capacity for liquids.

In subparagraph (c), amend the first sentence to read Rigid plastics IBCs the IBC shall be filled to not less than 95 of its maximum capacity for solids or 98 of its maximum capacity for liquids.

4.1.3.6 Pressure receptacles for liquids and solids

6.5.4.4.2 Every metal, rigid plastics and composite IBC for liquids, or for solids which are filled or discharged under pressure, shall undergo a suitable leakproofness test and be capable of meeting the test level indicated in 6.5.6.7.3

(a) in an ullage condition liable to produce an unacceptable hydraulic force due to surge within the portable tank

contents of 5 kg or less for solids.

328 This entry applies to fuel cell cartridges containing flammable liquids including methanol or methanol water solutions.

347. Annex II to MARPOL 73 78 sets out special requirements with respect to the control of pollution by noxious liquid substances carried in bulk.

For flammable liquids, Packing Group II, amend in the last column to read 1 litre .

combination packagings having inner packagings containing liquid dangerous goods

The disbandment of illegal groups process is a follow on programme to disband illegal militia who remain armed.

This device shall also prevent an unacceptable amount of leakage of liquid in the case of overturning or entry of foreign matter into the tank.

The amendments, when in force, will replace the existing text of paragraph 6 of regulation 5 on stowage and securing and make it clear that all cargoes, other than solid and liquid bulk cargoes , should be loaded, stowed and secured in accordance with the Cargo Securing Manual.

4.2.1.9.3 The maximum degree of filling (in ) for liquids of Division 6.1 and Class 8, in Packing Groups I and II, and liquids with an absolute vapour pressure of more than 175 kPa (1.75 bar) at 65 ºC, is determined by the formula

4.2.1.9.5.1 The maximum degree of filling (in ) for liquids transported under elevated temperature conditions is determined by the formula

TP3 For liquids transported under elevated temperature conditions the filling limits prescribed in 4.2.1.9.5.1 shall be met.

4.2.1.10.1 All portable tanks intended for the transport of flammable liquids shall be closed and be fitted with relief devices in accordance with 6.6.2.8 to 6.6.2.15.

(a) Measures to disband parastatal armed groups

(f) Wastes of UN No. 3291 containing sharp objects shall only be transported in UN type tested and approved rigid packagings meeting the provisions of packing instructions P621, IBC620 or LP621.

The handle enables you to hold it when the container is filled with hot liquid.

The liquid is actually that clear liquid.

6.6.4 Requirements for the design, construction, inspection and testing of portable tanks intended for the transport of refrigerated liquefied gases

Parts and components of liquid propellant surface to air missiles can also be reused in a surface to surface role, like the liquid propellant engines of the SA 2 missiles used in the Samoud 2 surface to surface missiles.

21. NASDA has implemented the draining of residual propellants (LOX, LH2, N2H4) and residual helium gas of the second stage of the H I and H II launcher.

The parties also agreed to proceed immediately with the disarmament and dismantling of militias and armed groups throughout the country.

A pipette bulb is used to fill pipettes. Squeezing then releasing the bulb produces a negative pressure, causing fluid to flow into the pipette squeezing the bulb then causes the fluid to flow out of the pipette.

4.2.2.6 Empty portable tanks not cleaned and not gas free shall comply with the same requirements as portable tanks filled with the previous non refrigerated liquefied gas.

6.6.3 Requirements for the design, construction, inspection and testing of portable tanks intended for the transport of non refrigerated liquefied gases

6.6.4.2.8 A reference holding time shall be determined for each refrigerated liquefied gas intended for transport in a portable tank.

Add a new 4.3.2.4 to read as follows 4.3.2.4 Bulk waste goods of Division 6.2 (UN Nos. 2814 and 2900 (animal carcasses only)) .

Filling density means the average mass of non refrigerated liquefied gas per litre of shell capacity (kg l).

6.6.3.7.3 Portable tanks intended for the transport of certain non refrigerated liquefied gases identified in portable tank instruction T50 in 4.2.4.2.6 shall have a pressure relief device approved by the competent authority.

6.6.4.6.2 Shells for non flammable refrigerated liquefied gases and hydrogen may in addition have frangible discs in parallel with the spring loaded devices as specified in 6.6.4.7.2 and 6.6.4.7.3.

(d) If there is any doubt as to whether or not residual liquid may be present in the primary receptacle during transport then a packaging suitable for liquids, including absorbent materials, shall be used.

During filling, the temperature of the refrigerated liquefied gas shall be within the limits of the design temperature range.

6.6.3.2.3 Gaskets shall be made of materials compatible with the non refrigerated liquefied gas(es) intended to be transported.

Maximum permissible load mass for each non refrigerated liquefied gas permitted _kg Maximum permissible gross mass (MPGM)_kg

Amend subparagraph (b) to read as follows Flexible IBCs the IBC shall be filled to the maximum permissible gross mass, the contents being evenly distributed. .

Liquid War

Water is a liquid.

Water is liquid.

Liquid Pouring

This device should also prevent an unacceptable amount of leakage of liquid in the case of overturning or entry of foreign matter into the tank.

(c) Sprut MBI determination of volumes of intra and extra cellular fluid, total circulating blood volume and the proportion of cellular and fluid blood components in the human body under conditions of weightlessness

It's filled with petrifying liquid. And it works.