4.1.3.6 Pressure receptacles for liquids and solids

(a) in an ullage condition liable to produce an unacceptable hydraulic force due to surge within the portable tank

contents of 5 kg or less for solids.

But today it's most widely used in office buildings in the sprinkler system as a fire suppression fluid.

I got fed up with man taking a daily hammer and sicklecoated pill of venom.

328 This entry applies to fuel cell cartridges containing flammable liquids including methanol or methanol water solutions.

For flammable liquids, Packing Group II, amend in the last column to read 1 litre .

combination packagings having inner packagings containing liquid dangerous goods

This device shall also prevent an unacceptable amount of leakage of liquid in the case of overturning or entry of foreign matter into the tank.

4.2.1.9.3 The maximum degree of filling (in ) for liquids of Division 6.1 and Class 8, in Packing Groups I and II, and liquids with an absolute vapour pressure of more than 175 kPa (1.75 bar) at 65 ºC, is determined by the formula

4.2.1.9.5.1 The maximum degree of filling (in ) for liquids transported under elevated temperature conditions is determined by the formula

TP3 For liquids transported under elevated temperature conditions the filling limits prescribed in 4.2.1.9.5.1 shall be met.

4.2.1.10.1 All portable tanks intended for the transport of flammable liquids shall be closed and be fitted with relief devices in accordance with 6.6.2.8 to 6.6.2.15.

Metal IBCs the IBC shall be filled to not less than 95 of its maximum capacity for solids or 98 of its maximum capacity for liquids.

The handle enables you to hold it when the container is filled with hot liquid.

The liquid is actually that clear liquid.

6.6.4 Requirements for the design, construction, inspection and testing of portable tanks intended for the transport of refrigerated liquefied gases

Parts and components of liquid propellant surface to air missiles can also be reused in a surface to surface role, like the liquid propellant engines of the SA 2 missiles used in the Samoud 2 surface to surface missiles.

21. NASDA has implemented the draining of residual propellants (LOX, LH2, N2H4) and residual helium gas of the second stage of the H I and H II launcher.

A pipette bulb is used to fill pipettes. Squeezing then releasing the bulb produces a negative pressure, causing fluid to flow into the pipette squeezing the bulb then causes the fluid to flow out of the pipette.

4.2.2.6 Empty portable tanks not cleaned and not gas free shall comply with the same requirements as portable tanks filled with the previous non refrigerated liquefied gas.

6.6.3 Requirements for the design, construction, inspection and testing of portable tanks intended for the transport of non refrigerated liquefied gases

6.6.4.2.8 A reference holding time shall be determined for each refrigerated liquefied gas intended for transport in a portable tank.

Filling density means the average mass of non refrigerated liquefied gas per litre of shell capacity (kg l).

6.6.3.7.3 Portable tanks intended for the transport of certain non refrigerated liquefied gases identified in portable tank instruction T50 in 4.2.4.2.6 shall have a pressure relief device approved by the competent authority.

6.6.4.6.2 Shells for non flammable refrigerated liquefied gases and hydrogen may in addition have frangible discs in parallel with the spring loaded devices as specified in 6.6.4.7.2 and 6.6.4.7.3.

(d) If there is any doubt as to whether or not residual liquid may be present in the primary receptacle during transport then a packaging suitable for liquids, including absorbent materials, shall be used.

During filling, the temperature of the refrigerated liquefied gas shall be within the limits of the design temperature range.

6.6.3.2.3 Gaskets shall be made of materials compatible with the non refrigerated liquefied gas(es) intended to be transported.

Maximum permissible load mass for each non refrigerated liquefied gas permitted _kg Maximum permissible gross mass (MPGM)_kg

Liquid War

Water is a liquid.

Water is liquid.

Liquid Pouring

In subparagraph (c), amend the first sentence to read Rigid plastics IBCs the IBC shall be filled to not less than 95 of its maximum capacity for solids or 98 of its maximum capacity for liquids.

15 The portable tank may be fitted with a device located under maximum filling conditions in the vapour space of the shell to prevent the build up of excess pressure due to the slow decomposition of the substance transported.

Anything else... sir?

This device should also prevent an unacceptable amount of leakage of liquid in the case of overturning or entry of foreign matter into the tank.

(c) Sprut MBI determination of volumes of intra and extra cellular fluid, total circulating blood volume and the proportion of cellular and fluid blood components in the human body under conditions of weightlessness

It's filled with petrifying liquid. And it works.

6.6.4.5.4 For sections of piping which can be closed at both ends and where liquid product can be trapped, a method of automatic pressure relief shall be provided to prevent excess pressure build up within the piping.

6.6.3.2.5 The materials of the portable tank, including any devices, gaskets, and accessories, shall not adversely affect the non refrigerated liquefied gases intended for transport in the portable tank.

FluidBalls

Demo Liquid

During filling, the temperature of the non refrigerated liquefied gas shall fall within the limits of the design temperature range.