For flammable liquids, Packing Group II, amend in the last column to read 1 litre .

328 This entry applies to fuel cell cartridges containing flammable liquids including methanol or methanol water solutions.

4.1.3.6 Pressure receptacles for liquids and solids

4.2.1.9.3 The maximum degree of filling (in ) for liquids of Division 6.1 and Class 8, in Packing Groups I and II, and liquids with an absolute vapour pressure of more than 175 kPa (1.75 bar) at 65 ºC, is determined by the formula

Shell means the part of the portable tank which retains the refrigerated liquefied gas intended for transport, including openings and their closures, but does not include service equipment or external structural equipment

Shell means the part of the portable tank which retains the non refrigerated liquefied gas intended for transport (tank proper), including openings and their closures, but does not include service equipment or structural equipment

(a) in an ullage condition liable to produce an unacceptable hydraulic force due to surge within the portable tank

contents of 5 kg or less for solids.

(d) If there is any doubt as to whether or not residual liquid may be present in the primary receptacle during transport then a packaging suitable for liquids, including absorbent materials, shall be used.

Solutions with not less than 50 but not more than 80 acid, by mass, should be placed in Packing Group II.

Beer is basically liquid bread, or bread is solid beer.

275 Solutions with more than 10 and less than 50 acid, by mass, should be placed in Packing Group III.

Inner packagings containing liquids shall be packaged with their closures upward and placed within outer packagings consistent with the orientation markings prescribed in 5.2.1.6 of these Regulations. .

combination packagings having inner packagings containing liquid dangerous goods

This device shall also prevent an unacceptable amount of leakage of liquid in the case of overturning or entry of foreign matter into the tank.

4.2.1.9.5.1 The maximum degree of filling (in ) for liquids transported under elevated temperature conditions is determined by the formula

TP3 For liquids transported under elevated temperature conditions the filling limits prescribed in 4.2.1.9.5.1 shall be met.

4.2.1.10.1 All portable tanks intended for the transport of flammable liquids shall be closed and be fitted with relief devices in accordance with 6.6.2.8 to 6.6.2.15.

Metal IBCs the IBC shall be filled to not less than 95 of its maximum capacity for solids or 98 of its maximum capacity for liquids.

The handle enables you to hold it when the container is filled with hot liquid.

The liquid is actually that clear liquid.

6.6.4 Requirements for the design, construction, inspection and testing of portable tanks intended for the transport of refrigerated liquefied gases

Parts and components of liquid propellant surface to air missiles can also be reused in a surface to surface role, like the liquid propellant engines of the SA 2 missiles used in the Samoud 2 surface to surface missiles.

21. NASDA has implemented the draining of residual propellants (LOX, LH2, N2H4) and residual helium gas of the second stage of the H I and H II launcher.

A pipette bulb is used to fill pipettes. Squeezing then releasing the bulb produces a negative pressure, causing fluid to flow into the pipette squeezing the bulb then causes the fluid to flow out of the pipette.

(f) Wastes of UN No. 3291 containing sharp objects shall only be transported in UN type tested and approved rigid packagings meeting the provisions of packing instructions P621, IBC620 or LP621.

4.2.2.6 Empty portable tanks not cleaned and not gas free shall comply with the same requirements as portable tanks filled with the previous non refrigerated liquefied gas.

6.6.3 Requirements for the design, construction, inspection and testing of portable tanks intended for the transport of non refrigerated liquefied gases

6.6.4.2.8 A reference holding time shall be determined for each refrigerated liquefied gas intended for transport in a portable tank.

In the case of rape perpetrated by someone the victim did not know, containers for a vaginal swab and two smears are provided in the kit, in addition to a comb for examining the pubic hair for foreign material, such as hair and pubic lice, as well as tubes for blood group determination, saliva tubes and containers for samples of any foreign body fluids, such as semen and blood.

Filling density means the average mass of non refrigerated liquefied gas per litre of shell capacity (kg l).

6.6.3.7.3 Portable tanks intended for the transport of certain non refrigerated liquefied gases identified in portable tank instruction T50 in 4.2.4.2.6 shall have a pressure relief device approved by the competent authority.

6.6.4.6.2 Shells for non flammable refrigerated liquefied gases and hydrogen may in addition have frangible discs in parallel with the spring loaded devices as specified in 6.6.4.7.2 and 6.6.4.7.3.

During filling, the temperature of the refrigerated liquefied gas shall be within the limits of the design temperature range.

6.6.3.2.3 Gaskets shall be made of materials compatible with the non refrigerated liquefied gas(es) intended to be transported.

Maximum permissible load mass for each non refrigerated liquefied gas permitted _kg Maximum permissible gross mass (MPGM)_kg

6.6.4.2.2 Any part of a portable tank, including fittings, gaskets and pipe work, which can be expected normally to come into contact with the refrigerated liquefied gas transported shall be compatible with that refrigerated liquefied gas.

Liquid War

Water is a liquid.

Water is liquid.

Liquid Pouring

In subparagraph (c), amend the first sentence to read Rigid plastics IBCs the IBC shall be filled to not less than 95 of its maximum capacity for solids or 98 of its maximum capacity for liquids.

Shape memory polymers are commercially available in a number of convenient physical states, including pellets, solutions and liquids.

This device should also prevent an unacceptable amount of leakage of liquid in the case of overturning or entry of foreign matter into the tank.

The pressure relief devices shall be of a type that will resist dynamic forces including liquid surge.